Before you begin your repair, you will need to remove Bob's battery.
Bob’s battery is located on his underside, just above his main brush. Use a Phillips head screwdriver to remove the two screws securing the battery cover.
Remove the battery cover and lift the battery out of its compartment.
To disconnect Bob’s battery, pinch and pull at the circuit junction.
Now you are ready to open up Bob and replace his power switch. Make sure Bob’s side power switch is turned OFF and flip him over onto a flat surface. Remove the screw securing Bob’s main brush in place.
Remove Bob’s main brush to remove the screw located beneath it (depending on Bob's model, there may be 2 screws).
Remove the 5 screws lining Bob’s underside.
Flip Bob back onto his wheels and lift his cover up. To remove Bob’s cover completely, you must detach 3 circuit plugs from his main board. Pinch the small white tab on the side of each circuit plug and pull upwards to remove it.
Slide Bob’s power inlet out and place his cover aside.
In order to access Bob’s power switch, you will first need to remove Bob’s main board. To do this, detach all of the remaining circuit plugs. Remember where each plug belongs, as you will need to reattach them after your repair.
Next, remove the 3 screws securing the main board in place.
Lift the main board out.
Slide the power switch out of its spot on Bob's bottom right side.
The power switch's wires are secured inside of Bob's battery compartment. Remove the screw on the bottom left corner of the battery compartment.
Lift the black plastic cap out.
Pull the power switch's wires out of the battery compartment.
Slide the replacement power switch into the empty spot on Bob's side.
Place the power switch's wires into the battery compartment through the hole in the compartment's bottom left corner, and cover the hole with the black plastic cap.
Replace the screw on the bottom left corner of the battery compartment.
You may now begin reconnecting all of the main board's circuit plugs. Make sure the main board lies flat over the empty screw posts and replace the 3 screws.
Left edge of the main board:
The small circuit plug with yellow and black wires attaches to the top of the main board’s left edge.
3 circuit plugs attach below the previous plug in the following order: a medium-sized plug with two pairs of twisted wires, one red and white, the other pink and black; a wide circuit plug with multicolored wires; and a small circuit plug with blue and black twisted wires (shown empty).
Bottom edge of the main board:
The wide circuit plug with multicolored wires — the plug for Bob’s right wheel — attaches to the far right of the main board’s bottom edge.
3 circuit plugs attach the left of the previous plug in the following order: a small plug with orange and black wires; a small plug with yellow wires; a medium-sized plug with red, brown, black, and white wires.
Leave the remaining 3 spaces on the bottom edge empty.
Right edge of the main board:
The circuit plug with the orange and black wires — the plug for Bob’s power inlet — attaches to the bottom of the main board's right edge.
The wide circuit plug with the red, black, and blue wires attaches above the previous plug.
Top edge of the main board:
2 wide circuit plugs attach to the main board’s top edge. Plug in the one on the left; leave the one on the right empty.
Now you’re ready to put Bob’s cover back together. First, reattach all the circuit plugs you removed to separate Bob's cover. Press down on each circuit plug to ensure it securely locks in place.
Before closing Bob's cover, slide his power inlet back in its place.
Carefully realign the edges of Bob’s cover and flip him onto his back. Replace the 5 screws on his underside to seal his cover together.
Replace the 1 or 2 screws located beneath Bob's main brush.
Place the main brush back in its compartment. Attach the end piece first
and align the square end with the square-shaped notch inside Bob.
Lastly, replace the screw securing Bob's main brush in place.
Don't forget to replace Bob's battery! Reconnect the battery at the circuit junction.
Tuck the wire into the side of Bob’s battery compartment and slide the battery in.
Finally, replace Bob’s battery cover so that it lays flat and replace the 2 screws. Your repair is now complete!