Welcome to bObsweep's Support Community!

Mingle, ask questions, and share ideas with your bObsweep family around the world.

New to the community? Start here.

Replacing Power Switch - Bob Standard (1001 series)

For this repair, you will need a Phillips head screwdriver and a power switch.

Before you begin your repair, you will need to remove Bob's battery. Bob’s battery is located on his underside, just above his main brush. Use a Phillips head screwdriver to remove the two screws securing the battery cover.

Remove the battery cover and lift the battery out of its compartment.

To disconnect Bob’s battery, pinch and pull at the circuit junction.

Make sure Bob’s side power switch is turned OFF and flip him over onto a flat surface. Remove the screw securing Bob’s main brush in place.

Remove Bob’s main brush to access and remove the screw located beneath it (depending on Bob's model, there may be 2 screws).

Remove the 5 screws lining Bob’s underside.

Flip Bob back onto his wheels and lift his cover up. Slid the power inlet out of its space.

powerswitch.jpg

To remove Bob’s cover completely, detach 4 circuit plugs from the mainboard. Pinch the small white tab on the side of each circuit plug and pull upwards to remove it.

bottomcovercircuit.jpg

topcovercircuit.jpg

Place the cover aside for later reassembly.

To access the speaker, you'll first need to remove the mainboard. Disconnect all remaining 12 circuit plugs from the mainboard.

Remove the 3 screws securing the mainboard in place.

Lift the mainboard out.

Slide the power switch out of its spot on Bob's bottom right side.

The power switch's wires are secured inside of Bob's battery compartment. Remove the screw on the bottom left corner of the battery compartment.

Lift the black plastic cap out.

Pull the power switch's wires out of the battery compartment.

Slide the replacement power switch into the empty spot on Bob's side.

Place the power switch's wires into the battery compartment through the hole in the compartment's bottom left corner, and cover the hole with the black plastic cap.

Replace the screw on the bottom left corner of the battery compartment.

Align the holes on the mainboard with the 3 screw posts on Bob’s interior. Ensure that the mainboard sits flat before replacing the 3 screws.

You may now begin reconnecting all of the mainboard's circuit plugs.

Left edge of the mainboard: 

The order of plugs on the left side of the mainboard, from left to right, is:

  • A small plug with black and yellow wires
  • A plug with two pairs of twisted wires
  • A plug with multi-colored wires for Bob’s left wheel
  • A plug with blue and black wires

left_edge.jpg

Bottom edge of the mainboard:

The order of plugs on the bottom of the mainboard, from left to right is:

  • Two open spaces
  • A small circuit plug with a red wire
  • One more open space
  • A small plug with yellow wires
  • A plug with multi-colored wires

bottom_edge.jpg

Right edge of the mainboard:

The order of plugs on the right side of the mainboard, from left to right is:

  • A plug with black and orange wires for Bob's power inlet
  • A wide circuit plug for Bob's power switch

right_edge.jpg

Top edge of the mainboard:

The order of plugs at the top of the mainboard, from left to right, is:

  • A small plug with black and orange wires
  • Two empty spaces
  • A wide plug with multicoloured wires
  • A small plug with red and green wires

top_edge.jpg

Now you’re ready to put Bob’s cover back together. First, reattach all the circuit plugs you removed to separate Bob's cover. Press down on each circuit plug to ensure it securely locks in place.

topcovercircuit.jpg

bottomcovercircuit.jpg

Before closing Bob's cover, slide his power inlet back in its place.

Carefully realign the edges of Bob’s cover and flip him onto his back. Replace the 5 screws on his underside to seal his cover together.

Replace the 1 or 2 screws located beneath Bob's main brush.

Place the main brush back in its compartment. Attach the end piece first

and align the square end with the square-shaped notch inside Bob.

Lastly, replace the screw securing Bob's main brush in place and your repair is complete!

Have more questions? Submit a request